>Home>Products>

uses of 10 mm aggregate:

differences in concrete properties using 10mm to 20mm ...

Dec 16, 2014  Depending on the mix design, either can be used to make essentially any range of concrete strengths. When you use a smaller aggregate, such as the 10mm as your nominal coarse aggregate size, the specific surface area of the total volume of coarse aggregate is much higher than for the 20mm aggregate.

Read More
Different sizes of Aggregate and their uses - YouTube

Aug 14, 2018  friends we use different sizes such as 40 mm, 20 mm,10 mm, aggregates so we use theses aggregate in different conditions. In this lecture i discussed these t...

Read More
What should be the ratio of 20mm to 10mm size aggregates ...

Aggregates make up some 60 -80% of the concrete mix. • Aggregates are divided into either ‘coarse’ or ‘fine’ categories. - Coarse aggregates are particulates that are greater than 4.75mm. The usual range employed is between 9.5mm and 37.5mm in dia...

Read More
1 ton 10mm 20mm 40mm aggregate convert to m3 - Civil Sir

Nov 22, 2020  1 ton 10mm 20mm 40mm aggregate convert to m3, hi guys in this article we know about 1 ton aggregate (stone chips) weight convert into cubic metre (m3) of different size 10mm, 20mm and 40 mm. Aggregate another name is stone chips categorised into two types of fine aggregate and coarse aggregate.

Read More
Uses of Aggregates in Construction, Roads, Railway and Other

Aug 30, 2017  Aggregates are the most mined material in the world. Construction aggregate is a broad category of granular raw material of different sizes (sand, gravel, crushed stone, slag, recycled concrete etc) used in construction. Aggregate can be used in a number of ways in construction. In roads and railway ballast the aggregates are used to resist the overall (static as well as

Read More
Specific Gravity and Water Absorption Tests on Aggregates ...

Feb 22, 2010  There are three methods of testing for the determination of the specific gravity of aggregates, according to the size of the aggregates larger than 10 mm, 40 mm and smaller than 10 mm. For Samples larger than 10 mm, 40 mm, the below given test method is used and for samples smaller than 10 mm Pycnometer test is done.

Read More
What happened when we not used 20 mm size aggregate in ...

Your question is not clear. Do you want to use concrete with nominal maximum size of aggregate less than 20 mm (i.e. 10 mm, 12.5 mm or 6.3 mm) or you wish to have concrete with say NMSA 40 mm and jumping to 10 mm while grading. Scenario 1: This is...

Read More
Density of Aggregate - Bulk and Relative Density - Civil ...

Key Features: If the volume is unit then, Bulk Density= Mass. Unit in kg/m 3 or lb/ft 3. In this definition, the volume is that contains both the aggregates and the voids between aggregates particles. The approximate bulk density of aggregate that is commonly used in normal-weight concrete is between 1200-1750 kg/m3 (75-110 lb/ft3) .

Read More
How To Do Sieve Analysis Of Aggregate

Nov 09, 2014  The sieves number that you will use in the 20 size aggregate samples are 37.5 mm, 20.0 mm, 14.0 mm, 10.0 mm 0.075 mm. Place the bigger size of sieve on top of smaller and in order from from top to bottom. And then put the dried sample on topmost sieve (37.5 mm) be careful on placing the sample to avoid throwing out of some pieces of aggregate ...

Read More
10mm Shingle - Ashville Aggregates - Aggregates Supplier

10mm Shingle, or as you may know it 10mm gravel or 10mm pea shingle gravel is a multi-purpose aggregate used for domestic, construction and commercial projects. This material consists of a mix of angular and rounded gravel that has been screened in

Read More
What should be the ratio of 20mm to 10mm size aggregates ...

Aggregates make up some 60 -80% of the concrete mix. • Aggregates are divided into either ‘coarse’ or ‘fine’ categories. - Coarse aggregates are particulates that are greater than 4.75mm. The usual range employed is between 9.5mm and 37.5mm in dia...

Read More
Use of ceramic wastes as aggregates in concrete production ...

Liu et al. recommended maximum size of 10 mm for ceramic tile aggregates as the thickness of ceramic tiles often lies in the range of 3–10 mm. For the particle size range of 14–20 mm, Elçi [ 43 ] reported both the shape and flakiness index of tile aggregate as 100%, indicating highly angular, flat, and elongated aggregates.

Read More
Improve Your Shotcrete: Use Coarse Aggregates!

Taking into consideration that a shotcrete mixture containing aggregate measuring a maximum of 3/8 in. (10 mm) will often have traces of aggregate measuring 1/2 in. (12.7 mm), the minimum thickness at which this shotcrete mixture should be placed is 1 1/2 in. (38 mm). In conclusion, the use of coarse aggregate in shotcrete mixtures will provide ...

Read More
Sieve Analysis of Aggregates - Civil Engineering Portal ...

In this we use different sieves as standardized by the IS code and then pass aggregates through them and thus collect different sized particles left over different sieves. The apparatus used are – i) A set of IS Sieves of sizes – 80mm, 63mm, 50mm, 40mm,31.5mm, 25mm, 20mm, 16mm, 12.5mm, 10mm, 6.3mm,4.75mm, 3.35mm, 2.36mm, 1.18mm, 600µm ...

Read More
What is Lightweight Concrete? its 6 Types, Uses, Advantages

Jul 15, 2020  No fine concrete contains only a single size 10mm to 20mm coarse aggregate and is an agglomeration of coarse aggregate particles and each particle is surrounded by a coating of cement paste up to the thickness of about 1•3 mm. For its low strength, large pores within the body of the concrete are responsible but no capillary movement of water ...

Read More
Aggregate Impact value Test Apparatus, Procedure and uses ...

Jul 01, 2019  The test sample: normally aggregates sized 10.0 mm to 12.5 mm. the aggregates should be dried by heating at 100-110 0C for a period of 4 hours and cooled. Sieve the material through 12.5mm and 10.0 mm IS sieves. The aggregates passing through 12.5 mm sieve comprises the test material.

Read More
Density of Aggregate - Bulk and Relative Density - Civil ...

Key Features: If the volume is unit then, Bulk Density= Mass. Unit in kg/m 3 or lb/ft 3. In this definition, the volume is that contains both the aggregates and the voids between aggregates particles. The approximate bulk density of aggregate that is commonly used in normal-weight concrete is between 1200-1750 kg/m3 (75-110 lb/ft3) .

Read More
DOE Methods of Concrete Mix Design Concrete Technology

2. If fly ash is used along with cement, then water content may be reduced as shown in Table 20.48. Example 2: Design a concrete mix for targeted 28 days cube strength of 45 MPa from the following data: 1. Max. size of uncrushed aggregate to be used = 20 mm . 2. Low workability, slump = 10-30 mm . 3. Specific gravity of aggregate = 2.65 . 4.

Read More
Aggregate (20mm) - Building Materials - Construction ...

Aggregate is a component of composite materials such as concrete and asphalt concrete. It serves as reinforcement (adding strength to the overall composite material), and for forming concrete mortar (by mixing with water, bitumen, Portland cement, lime and gypsum). It is also used as base material under foundations, roads, and railroads.

Read More
Aggregates for Concrete - Civil Engineering

predominantly larger than 5 mm (0.2 in.) and generally between 9.5 mm and 37.5 mm (3⁄ 8 in. and 11⁄ 2 in.). Some natural aggregate deposits, called pit-run gravel, consist of gravel and sand that can be readily used in concrete after minimal processing. Natural gravel and sand are usually dug or dredged from a pit, river, lake, or seabed.

Read More
Travis Perkins Gravel and Shingle Bulk Bag 10mm Travis ...

This bulk bag of 10mm gravel and shingle consists of small stones that are ideal for mixing with other products when concreting and floor screeding. Other uses include backfilling drains and landscaping tasks. It is recommended that the 20mm version or one of the decorative aggregates is used for driveways and paths as the small stones can be brought inside on footwear.

Read More
standard density of 10mm stone aggregate 」

density of 10 mm stone aggregatePopular Education. in 1963 version of the standard, the provisions regarding bulk density have not been included.2.1.2 Crushed Stone SandFine aggregate produced . 20 mm. 16mm. 12.5 mm. 10 mm. 4.75 mm. 236mm.

Read More
Use of Waste Plastic in Flexible Pavements-Green Roads

Aggregates: 20 mm, 10 mm, 6 mm and stone dust were used for the present study whose sieve analysis is shown in Table 2. Table 3 shows the test results and permissible limits of the tests carried out to check the physical properties of aggregates. Aggregate Gradation DBM-II (50 - 75 Mm Thickness): Grading of the aggregates is done in the DBM layer

Read More
Uses for Construction Aggregates

Jan 07, 2019  The granite aggregates are found in various sizes that are 20-40mm, 10-20mm, 5-20mm, 5-10mm, 3-5 mm, 2-5mm, 0-2mm as well as 0-5 granite sand. The aggregates sizes are unique and serve a wide range of construction purposes. Crushed stone that is a fine dust or particle is often used

Read More
What should be the ratio of 20mm to 10mm size aggregates ...

Aggregates make up some 60 -80% of the concrete mix. • Aggregates are divided into either ‘coarse’ or ‘fine’ categories. - Coarse aggregates are particulates that are greater than 4.75mm. The usual range employed is between 9.5mm and 37.5mm in dia...

Read More
10 Mm Aggregates Specific Gravity

Apr 04, 2018  10 Mm Aggregates Specific Gravity. Objective for determination of specific gravity water absorption of aggregates.Reference standards is 2386 part 3 1963 method of test for aggregates for concrete part i particle size and shape.Equipment apparatus wire basket oven 3000c container for filling water and suspending the basket an air tight container balance0-10 kg.

Read More
10mm Concrete Aggregate Australian Steel Mill Services

10mm Concrete Aggregate. Download Product Data Sheet PDF. Product Code ABF210. ASMS ABF210 is a single sized 10 mm concrete aggregate conforming to AS2758.1. APPLICATIONS. ABF210 is manufactured as an aggregate for use in concrete. COMPOSITION AND MATERIALS

Read More
10mm Shingle - Ashville Aggregates - Aggregates Supplier

10mm Shingle, or as you may know it 10mm gravel or 10mm pea shingle gravel is a multi-purpose aggregate used for domestic, construction and commercial projects. This material consists of a mix of angular and rounded gravel that has been screened in order to remove fines.

Read More
Aggregates for Concrete - Civil Engineering

predominantly larger than 5 mm (0.2 in.) and generally between 9.5 mm and 37.5 mm (3⁄ 8 in. and 11⁄ 2 in.). Some natural aggregate deposits, called pit-run gravel, consist of gravel and sand that can be readily used in concrete after minimal processing. Natural gravel and sand are usually dug or dredged from a pit, river, lake, or seabed.

Read More
Replacement of Coarse Aggregate by Using Naturally ...

In this project, two types of coarse aggregates were used for preparation of concrete, Crushed Coarse Aggregate. (CAI CAII) and coconut shell Coarse Aggregate. (CSA) Coarse Aggregate of type I:- Crushed hard basalt chips of maximum size 10 mm were used in the concrete Mixes. Coarse Aggregate

Read More
A Detailed Guide on Grading of Aggregates.

The number of sieves is five for the coarse aggregates and ten for all-in-aggregates. It is only six in the case of fine aggregates. Sieve Size for Grading of Aggregates. Coarse Aggregates: 80 mm, 40 mm, 20 mm, 10 mm, IS Nos. 480. Fine Aggregates: IS No. 480, 240, 120, 60, 30 and 15. All in aggregates: 80 mm, 40 mm, 20 mm, 10 mm, Nos: 480, 240 ...

Read More
Aggregate Impact value Test Apparatus, Procedure and uses ...

Jul 01, 2019  The test sample: normally aggregates sized 10.0 mm to 12.5 mm. the aggregates should be dried by heating at 100-110 0C for a period of 4 hours and cooled. Sieve the material through 12.5mm and 10.0 mm IS sieves. The aggregates passing through 12.5 mm sieve comprises the test material.

Read More
How To Do Sieve Analysis Of Aggregate

Nov 09, 2014  The sieves number that you will use in the 20 size aggregate samples are 37.5 mm, 20.0 mm, 14.0 mm, 10.0 mm 0.075 mm. Place the bigger size of sieve on top of smaller and in order from from top to bottom. And then put the dried sample on topmost sieve (37.5 mm) be careful on placing the sample to avoid throwing out of some pieces of aggregate ...

Read More
Aggregate in Concrete - The Concrete Network

Important Aggregate Dos and Don'ts. DO use aggregate that's in compliance with ASTM C 33, "Standard Specifications for Concrete Aggregates." Aggregates must be sound, clean, hard, durable, and free of excessive fines or contaminates that can affect cement hydration or disrupt the paste-aggregate bond.

Read More
Concrete Mix Design - SlideShare

Mar 29, 2015  The ACI Method of Mix Design • Decide maximum size of aggregate to be Used. Generally RCC work 20 mm and Pre-stressed Concrete 10 mm Size are Used • Decide Workability in terms of slump for the type of job in hand. General guidance can be taken from table 9.12. 99.

Read More
Flakiness And Elongation Index Test Of Coarse Aggregate

May 23, 2020  Flakiness Index = weight of aggregate retained on length gauge of 10 mm to 6.3 mm (W2) / _ Total weight of aggregate sample taken (W1) = (W2/W1) x 100. For example, Weight of aggregate retained on length gauge of 10 mm to 6.3mm (W2) = 150 gm and Total weight of aggregate sample = 1000 gm. Elongation Index = (150 gm / 1000 gm) x 100 = 15%.

Read More
How to Calculate Quantities of Cement, Sand and Aggregate ...

If you want 10 mm and 20 mm aggregate mixed in the concrete, mix it in the ratio of 50:50 (of coarse aggregate volume). PCC should be usually be done with M15, so we haven’t given the ratio for M10. Chetan chougule. September 25, 2017 at 9:00 pm. I want to know m35 m 45 strength in peving block .

Read More